ZyXEL Communications USG-50 - V2.21 ED 1 Guía de usuario Pagina 229
- Pagina / 390
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 25 Device HA
ZyWALL (ZLD) CLI Reference Guide
229
25.4.2 Active-Passive Mode Device HA Command Example
This example configures a ZyWALL to be a master ZyWALL for active-passive mode device HA.
There is a management IP address of 192.168.1.3 on lan1. wan1 and lan1 are monitored. The
synchronization password is set to “mySyncPassword”.
25.5 Legacy Mode (VRRP) Device HA
This section covers device HA using VRRP, VRRP groups, and synchronization.
Virtual Router Redundancy Protocol (VRRP) Overview
Every computer on a network may send packets to a default gateway, which can become a single
point of failure. Virtual Router Redundancy Protocol (VRRP), allows you to create redundant backup
gateways to ensure that the default gateway is always available. The ZyWALL uses a custom VRRP
implementation and is not compatible with standard VRRP.
VRRP Group Overview
In the ZyWALL, you should create a VRRP group to add one of its interfaces to a virtual router. You
can add any Ethernet interface, VLAN interface, or virtual interface (created on top of Ethernet
interfaces or VLAN interfaces) with a static IP address. You can only enable one VRRP group for
each interface, and you can only have one active VRRP group for each virtual router.
25.6 Legacy Mode (VRRP) Device HA Commands
The following table identifies the values required for many device-ha commands. Other input
values are discussed with the corresponding commands.
The following sections list the
device-ha commands.
Router(config)# device-ha ap-mode lan1 manage-ip 192.168.1.3 255.255.255.0
Router(config)# device-ha ap-mode role master
Router(config)# device-ha ap-mode master sync authentication password mySyncPassword
Router(config)# device-ha ap-mode wan1 activate
Router(config)# device-ha ap-mode lan1 activate
Router(config)# device-ha activate
Table 127 Input Values for device-ha Commands
LABEL DESCRIPTION
vrrp_group_name The name of the VRRP group. The name can consist of alphanumeric characters, the
underscore, and the dash and may be up to fifteen alphanumeric characters long.
- USG ZyWALL Series 1
- Intended Audience 3
- How To Use This Guide 3
- Document Conventions 4
- Document Conventions 5
- Contents Overview 7
- Table of Contents 10
- Table of Contents 11
- Chapter 38 18
- Introduction 21
- CHAPTER 1 23
- 1.2.1 Console Port 24
- Router(config)# 26
- 1.2.3 Telnet 27
- 1.2.4 SSH (Secure SHell) 27
- 1.5 CLI Modes 29
- 1.6 Shortcuts and Help 30
- 1.7 Input Values 32
- TAG # VALUES LEGAL VALUES 33
- 1.8 Ethernet Interfaces 35
- 1.10 Logging Out 36
- CHAPTER 2 37
- 2.1.1 Debug Commands 38
- Reference 41
- CHAPTER 3 43
- CHAPTER 4 45
- Chapter 4 Status 46
- Chapter 4 Status 47
- CHAPTER 5 49
- 5.2 Registration Commands 50
- 5.2.1 Command Examples 51
- 5.3 Country Code 52
- Chapter 5 Registration 56
- CHAPTER 6 57
- Chapter 6 Interfaces 62
- Chapter 6 Interfaces 63
- 6.2.2 DHCP Setting Commands 67
- 6.2.4 RIP Commands 72
- 6.2.5 OSPF Commands 72
- 6.3.2 Port Grouping Commands 76
- 6.6.1 Cellular Status 82
- Table 28 Cellular Status 83
- STATUS DESCRIPTION 83
- 6.9 WLAN Specific Commands 87
- 6.9.1 WLAN General Commands 88
- CHAPTER 7 97
- 7.4 Trunk Commands Summary 98
- 7.5 Trunk Command Examples 99
- 7.6 Link Sticking 100
- Chapter 7 Trunks 102
- CHAPTER 8 103
- Chapter 8 Route 105
- COMMAND DESCRIPTION 105
- Chapter 8 Route 106
- 8.4 Static Route Commands 109
- 8.3 IP Static Route 109
- CHAPTER 9 111
- 9.2.1 RIP Commands 112
- 9.2.2 General OSPF Commands 112
- 9.2.3 OSPF Area Commands 113
- 9.2.4 Virtual Link Commands 113
- CHAPTER 10 115
- 10.2 Zone Commands Summary 116
- 10.2.1 Zone Command Examples 117
- Chapter 10 Zones 118
- CHAPTER 11 119
- 11.2 DDNS Commands Summary 120
- Chapter 11 DDNS 121
- Chapter 11 DDNS 122
- CHAPTER 12 123
- Chapter 12 Virtual Servers 124
- 192.168.3.7 126
- CHAPTER 13 127
- 13.2 HTTP Redirect Commands 128
- Chapter 13 HTTP Redirect 129
- Chapter 13 HTTP Redirect 130
- CHAPTER 14 131
- 14.2 ALG Commands 132
- 14.3 ALG Commands Example 133
- Chapter 14 ALG 134
- CHAPTER 15 135
- Chapter 15 IP/MAC Binding 136
- IP/MAC binding status 136
- CHAPTER 16 137
- 16.2 Firewall Commands 138
- Chapter 16 Firewall 139
- Chapter 16 Firewall 140
- 16.2.1 Firewall Sub-Commands 141
- 16.3 Session Limit Commands 143
- means all IP addresses 144
- CHAPTER 17 145
- 17.2.1 IKE SA Commands 147
- Chapter 17 IPSec VPN 150
- 17.2.6 SA Monitor Commands 153
- CHAPTER 18 155
- 18.2.1 SSL VPN Commands 156
- Chapter 18 SSL VPN 159
- Chapter 18 SSL VPN 160
- CHAPTER 19 161
- 19.3 Policy Route 162
- 19.4 L2TP VPN Commands 163
- 19.5 L2TP VPN Example 164
- CHAPTER 20 167
- 20.2.2.1 Rule Sub-commands 169
- Chapter 20 Application Patrol 174
- CHAPTER 21 177
- Chapter 21 Anti-Virus 179
- 21.2.3 White and Black Lists 180
- 21.4 Anti-virus Statistics 183
- Chapter 21 Anti-Virus 184
- CHAPTER 22 185
- 22.3 IDP Profile Commands 186
- old_profile new_profile 187
- Chapter 22 IDP Commands 189
- Chapter 22 IDP Commands 190
- 22.3.6 Signature Search 192
- If you want to 194
- 22.4 IDP Custom Signatures 195
- 22.5 Update IDP Signatures 199
- 22.6 IDP Statistics 200
- CHAPTER 23 203
- Chapter 23 Content Filtering 204
- LABEL DESCRIPTION 204
- Chapter 5 on page 49) 211
- 8 Activate the customization 212
- Chapter 23 Content Filtering 213
- CHAPTER 24 215
- Chapter 24 Anti-Spam 217
- 24.2.3 White and Black Lists 218
- Table 122 DNSBL Commands 221
- 24.2.4.1 DNSBL Example 222
- 24.3 Anti-Spam Statistics 223
- Chapter 24 Anti-Spam 224
- CHAPTER 25 225
- 25.1.1 Before You Begin 226
- #%^*={}:,.~ characters 228
- VRRP Group Overview 229
- 25.6.1 VRRP Group Commands 230
- Chapter 25 Device HA 232
- CHAPTER 26 233
- 26.2.1 User Commands 234
- 26.2.2 User Group Commands 235
- 26.2.3 User Setting Commands 235
- Chapter 26 User/Group 236
- Chapter 26 User/Group 237
- CHAPTER 27 241
- Chapter 27 Addresses 243
- ()+/:=?!*#@$_% 245
- Chapter 27 Addresses 246
- CHAPTER 28 247
- Chapter 28 Services 250
- CHAPTER 29 251
- CHAPTER 30 253
- 30.2.2 ldap-server Commands 254
- CHAPTER 31 259
- 31.3 test aaa Command 260
- CHAPTER 32 263
- characters 264
- Chapter 32 Certificates 265
- Chapter 32 Certificates 266
- CHAPTER 33 268
- CHAPTER 34 270
- Chapter 34 SSL Application 271
- Chapter 34 SSL Application 272
- CHAPTER 35 273
- Requirements 274
- Chapter 35 Endpoint Security 275
- Chapter 35 Endpoint Security 276
- CHAPTER 36 280
- CHAPTER 37 283
- 37.3 Host Name Commands 285
- 37.4 Time and Date 285
- 37.5 Console Port Speed 286
- 37.6 DNS Overview 287
- 37.6.3 DNS Command Example 288
- CHAPTER 38 289
- 38.3 HTTP/HTTPS Commands 290
- 38.4 SSH 292
- 38.4.3 SSH Commands 293
- 38.4.4 SSH Command Examples 293
- 38.5 Telnet 294
- 38.6 Telnet Commands 294
- 38.7 Configuring FTP 295
- 38.8 SNMP 296
- 38.8.3 SNMP Commands 297
- 38.9 ICMP Filter 298
- 38.10 Dial-in Management 298
- 38.10.1 AT Command Strings 299
- 38.10.2 DTR Signal 299
- 38.10.3 Response Strings 299
- 38.11 Vantage CNM 300
- 38.12 Language Commands 301
- 38.13 IPv6 Commands 302
- CHAPTER 39 303
- Chapter 39 File Manager 307
- 39.6 FTP File Transfer 308
- 1. Boot Module 310
- 2. Recovery Image 310
- 3. Firmware 310
- Firmware 311
- CHAPTER 40 321
- 40.1.1 Log Entries Commands 322
- 40.1.2 System Log Commands 322
- 40.1.3 Debug Log Commands 323
- Chapter 40 Logs 325
- CHAPTER 41 327
- 41.1.3 Session Commands 328
- 41.3 Reboot 332
- CHAPTER 42 333
- Chapter 42 Session Timeout 334
- CHAPTER 43 335
- Chapter 43 Diagnostics 336
- CHAPTER 44 337
- CHAPTER 45 341
- Chapter 45 Packet Flow Filter 344
- CHAPTER 46 345
- Chapter 46 Maintenance Tools 346
- CHAPTER 47 351
- 47.3 Application Watchdog 352
- Chapter 47 Watchdog Timer 353
- Chapter 47 Watchdog Timer 354
- 383
Relacionado con productos y manuales para Gateways / Controladores ZyXEL Communications USG-50 - V2.21 ED 1
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales