Zyxel-communications omni.net Plus Manual de usuario Pagina 97
- Pagina / 186
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Technical Reference for ZyXEL omni.net series
8-9
X.75 Bundled Call
A bundle connection is initiated at the calling site by sending two consecutive SETUP messages to the
network. The two SETUP messages are all the same except for the Call Reference values.
[AT&Jn] can be used for bundle configuration as follows:
AT Command Description
AT&J0
Disables B-channel bundling.
AT&J1
Enables B-channel bundling in answer mode only.
AT&J2
Enables B-channel bundling in call mode only.
AT&J3
Enables B-channel bundling in both call and answer modes.
If channel bundling is enabled, the [ATDIs] command will generate two consecutive SETUP messages to
invoke bundle initiation.
For Northern Telecom ISDN, each BRI destination phone number can only be called once in any time. In order
to use two B channels for aggregation, we must place two calls with different phone numbers. The following
command can be used for this purpose:
& ATDI[phone_number_1]+[phone_number_2]
If the called site receives two consecutive SETUP messages with the same Calling Party Number and Bearer
Capability then it is deemed as a bundle request. The two data calls are established following normal call
control procedures. That is, the network treats them as two independent calls.
The omni.net uses X.75 Multiple Link Protocol or 'cFos' channel bundling protocol to coordinate the two
B-channels. The former would need an overhead of two octets for each packet. The success of bundle
connection initiation is indicated by the connect message reported to DTE as follows:
& CONNECT 460800 / X.75M 128K / V42b
If a B-channel is unavailable at either site then the bundle initiation will fall back to single channel connection. In
this case the connect message may be as follows:
& CONNECT 460800 / X.75 64000 / V42b
Table 50. X.75 Bundled Call
- ISDN Terminal Adapters 2
- Limited Warranty 3
- Become a Registered Owner 3
- Contents 5
- PART II ISDN FUNCTION 6
- PART III VOICE FEATURES 7
- PART IV DATA FUNCTION 8
- PART V FAX/MODEM FUNCTION 9
- PART VII APPENDICES 10
- Content of Tables 13
- Content of Figures 17
- Preface 18
- How to Use This Manual 19
- Other References 19
- Part I 21
- Introduction 21
- Chapter 1 23
- Intelligent Features 24
- Specifications 24
- Key Features Summary 25
- Chapter 2 27
- ISDN Configuration Manager 27
- Bumping 31
- Configuring ISDN Parameters 32
- Chapter 3 33
- LCD/LCD+M) 33
- LCD Panel Functions 34
- Right key: 35
- Left key: 35
- Up key: 35
- Down key: 35
- Idle Screen 36
- Set Clock sub-menu 36
- Set Display Mode sub-menu 36
- Dial In Log 37
- Stored Phone List 37
- Dial Out Log 38
- Active Status 39
- Clock Options 40
- Update Clock 41
- Set Display Mode 42
- Dial In Log Options 43
- button 44
- Dial Out Log Options 45
- Part II 47
- ISDN Function 47
- Chapter 4 49
- ISDN Communication Basics 49
- Supported AT Command Types 51
- LCD/LCD+M/Plus) 54
- Placing a Data Call 55
- Incoming Calls 55
- Command Description 58
- ATS119.3=0 58
- ATS119.3=1 58
- Best effort call answering 58
- Part III 61
- Voice Features 61
- Supplementary Service 63
- Chapter 5 63
- Call Waiting 64
- Call Hold/Retrieve 64
- Three Way Conferencing 66
- Starting a conference call 66
- Call Forwarding 68
- For DSS1 switch 68
- Chapter 6 71
- Feature Phone Operation 71
- Flash Key Commands 72
- InterCom 72
- Receiving a Second Call 73
- Call Broker 74
- Call Reject 75
- Call Transfer 75
- Three-Way Conference Call 76
- Last Number Redial 77
- Quick Dial 77
- Part IV 79
- Data Function 79
- Chapter 7 81
- Feature List 82
- Async to Sync Conversion 82
- Authentication Conversion 82
- Multilink PPP 84
- Call Bumping 84
- Bandwidth On Demand (BOD) 86
- BACP/BAP 86
- Chapter 8 89
- ISDN Communications 89
- V.110 Outgoing Protocol 91
- V.120 Outgoing Protocol 92
- X.75 Outgoing Protocol 93
- Speeds of 128Kbps 95
- V.120 Bundled Call 95
- X.75 Bundled Call 97
- Table 52. V.42bis AT Command 98
- Data Compression with X.75 100
- Security Settings 101
- Modifying the User Passwords 105
- Password: 106
- Part V 107
- Fax/Modem Function 107
- Chapter 9 109
- Internal Fax/Modem Function 109
- MNP Protocols 110
- Xmodem, Ymodem, and Zmodem 110
- Fax and Facsimile 111
- Modem as a fax 111
- EIA Class 1 Fax Commands 111
- Answering a Call Using MSN 113
- Control Data Compression 115
- Fax Operation 115
- Fax Command Sets 116
- Appendix D) 118
- Part VI 119
- Diagnostics 119
- Firmware Update 119
- Chapter 10 121
- Power-on Self-test 122
- Resetting Your omni.net 124
- Capturing the Protocol Data 125
- Analyzing the Captured Data 126
- Chapter 11 129
- Firmware Upgrade 129
- Kernel Mode 130
- Part VII 133
- Appendices 133
- Appendix A 135
- AT Command Set Reference 135
- AT Commands Description 136
- AT Commands Prefix (AT) 136
- Description of ATI3 Output 144
- Fax Command 151
- Appendix B 153
- Setting S-registers 154
- S-Register Descriptions 156
- Appendix C 181
- Appendix D 183
- Serial Port Interface 183
Relacionado con productos y manuales para Hardware Zyxel-communications omni.net Plus
Hardware Zyxel-communications NWA3160 Manual de usuario
(314 paginas)
(314 paginas)
(18 paginas)
(131 paginas)
Hardware Zyxel-communications 802.11g HomePlug AV ADSL2+ Gateway P-660HWP-D1 Manual de usuario
(13 paginas)
(13 paginas)
Hardware Zyxel-communications NWA3550 Manual de usuario
(344 paginas)
(344 paginas)
Hardware Zyxel-communications NWA570N Manual de usuario
(152 paginas)
(152 paginas)
Husqvarna 324LDX-Series manuals
Owner’s manuals and user’s guides for Petrol tool Husqvarna 324LDX-Series.
We providing 1 pdf manuals Husqvarna 324LDX-Series for download free by document types: User Manual
Comentarios a estos manuales