ZyXEL Confidential
P-660H-D1: For wan,enable RIP direction ”both”, version ”RIP-2M”,disable firewall, WAN mode:
ENETEcap,dynamicIP
P-2302HWUDL-P1: enable RIP”both”,version”RIP-2M” for LAN,LAN IP is 192.168.3.1,WAN IP.
Set static route:Destination 4.2.2.2 gateway:172.25.27.70) So P-660H-D1 can get an wan IP as
192.168.3.33
3.Problem
Ras ＞ ip rip sta
RIP: sent 438 rcvd 177 reqst 0 resp 0 unknown 0 refused 0
Errors:
version 177 addr family 0 target 0 gateway 0 mask 0 metric 0 MBZ 0
iface enif0: send RIP-2 only, recv Both
iface wanif0: send None, recv None
As here we note the wrong information of interface RIP status ,”iface wanif0“ should be”send RIP-2
only,recv Both”.
ras ＞ i r s
Dest FF Len Device Gateway Metric stat Timer Use
192.168.1.0 00 24 enet0 192.168.1.1 1 041b 0 35
192.168.3.0 00 24 mpoa00 192.168.3.33 1 042b 0 12
default 00 0 mpoa00 192.168.3.1 1 042b 0 5
More information, I set WAN IP of P-660H-D1 manually as 192.168.3.100, then I found the routing
table changed:
ras ＞ i r s
Dest FF Len Device Gateway Metric stat Timer Use
192.168.1.0 00 24 enet0 192.168.1.1 1 041b 0 227
192.168.3.0 00 24 mpoa00 192.168.3.100 2 00ab 0 4
4.2.2.2 00 24 mpoa00 192.168.3.1 2 00a9 160 0
172.25.0.0 00 16 mpoa00 192.168.3.1 3 00a9 160 0
default 00 0 mpoa00 192.168.3.1 2 00ab 0 3
”ip rip sta” also changed:
ras ＞ ip rip sta
RIP: sent 469 rcvd 205 reqst 0 resp 13 unknown 0 refused 0
Errors:
version 192 addr family 0 target 0 gateway 0 mask 0 metric 0 MBZ 0
iface enif0: send RIP-2 only, recv Both
iface wanif0: send RIP-2 only, recv Both
This is correct
Modifications in V 3.40(AGD.3)b1 | 04/21/2009
1.[BUG FIXED] SPRID: 060426075
Problem Symptom: In GUI-＞WAN ,Set two or more remote node, and use same encapsulation,different
VPI/VCI,set static IP. Then delete one rule and set the same setting in other remote node. Lan PC or device
ping the gateway, the device will crash.
Problem Condition: Step1:GUI- ＞ WAN set two remote node,and use same encapsulation,different
VPI/VCI, and set static IP. Lan PC ping remote node 2 gateway successfully. Setp2: Delete the remote
node 2, and set the same setting in other rule, such as remote node 5. Lan PC ping remote node 5 gateway,
the device will crash.
2.[BUG FIXED] SPRID: 060503121
Problem Symptom: Wan /more connections/ NAT edit lead to crash.
Problem Condition: Step1. Restore default setting. Step2. Enter WAN/More Connections, edit one of the
connections, then enter NAT SUA Only edit. After your apply it, It shows Address Mapping rule to edit,
Page 4 of 12
(21 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales