Zyxel-communications 1 Manual de usuario Pagina 130
- Pagina / 174
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
NetAtlas Enterprise 1.00 User’s Guide
129 Chapter 13 Ethernet Port Configuration
2 Click Configuration, Switch Configuration and then the Switch Setup tab.
3 Select the STP Configuration check box and then click Apply.
4 Click Configuration, Ethernet Port Configuration and then the Port STP tab.
5 Select the ports from the Port List Panel that you want to apply this configuration.
Figure 92 Configuration: Ethernet Port Configuration: Port STP
The following table describes the fields in this screen.
Table 51 Configuration: Ethernet Port Configuration: Port STP
LABEL DESCRIPTION
STP Active Select this check box to activate STP on this port.
Priority Priority is used in determining the root device, root port and designated port.
The device with the highest priority (lowest numeric value) becomes the
STP root device. If all devices have the same priority, the device with the
lowest MAC address will then become the root device. The allowed range is
0 to 255. The lower the numeric value you assign, the higher the priority for
this device.
Path Cost Path cost is the cost of transmitting a frame on to a LAN through that port. It
is assigned according to the speed of the link. The slower the media, the
higher the cost (refer to the table on path cost in the section on STP).
Apply Click Apply to save the changes back to the switch.
13.5 Bandwidth Control
Bandwidth control means defining a maximum allowable bandwidth for incoming and/or out-
going traffic flows on a port.
13.5.1 Configuring Bandwidth Control
Follow the steps below to configure the Bandwidth Control screen.
1 In the Device Panel list, select a device and then right-click.
2 Click Configuration, Switch Configuration and then the Switch Setup tab.
- NetAtlas Enterprise 1.00 1
- Copyright 3
- Federal Communications 4
- Statement 4
- Safety Warnings 5
- ZyXEL Limited Warranty 6
- Customer Support 7
- 7 Customer Support 8
- Table of Contents 9
- Chapter 12 12
- Chapter 13 12
- Chapter 14 13
- Chapter 15 13
- List of Figures 15
- 17 List of Figures 18
- List of Tables 19
- About This User's Guide 21
- Syntax Conventions 21
- Related Documentation 21
- User Guide Feedback 22
- CHAPTER 1 23
- 1.3.1 Installing the EMS 24
- Click Next to continue 27
- 1.4 SNMPc Network Manager 32
- 1.5 Adding MIBs 33
- MIB). Click OK 34
- 1.6 Finding your Switch 35
- 1.6.2 Add Device(s) Manually 36
- 1.7 Using SNMP 37
- Figure 29 Startup MySQL 40
- Sources list 41
- 3 Click Configure 41
- Figure 34 Switch Manager 42
- CHAPTER 2 45
- 2.2 Device Icon Colors 46
- 2.5 Menu Shortcut Buttons 47
- 2.6 EMS Main Menu Summary 47
- 47 Chapter 2 EMS Main Window 48
- 2.8 View the Switch 49
- 2.9 Switch Information 49
- 49 Chapter 2 EMS Main Window 50
- 2.10 Configuration Save 51
- 51 Chapter 2 EMS Main Window 52
- CHAPTER 3 53
- 3.1.2 Edit a Node 54
- 3.1.4 Delete a Submap 55
- 3.1.3 Find an Object 55
- 3.2 Exit 56
- CHAPTER 4 57
- 57 Chapter 4 VLAN Template 58
- Figure 46 Template: VLAN 58
- Table 12 Template: VLAN 58
- Chapter 4 58 59
- 59 Chapter 4 60
- CHAPTER 5 61
- 61 Chapter 5 Status 62
- 5.2 STP Status 63
- 5.2.2 How STP Works 64
- 5.2.3 STP Port States 65
- 5.2.4 View STP Status 65
- 5.3 VLAN Status 66
- 5.4 Port Status 67
- 67 Chapter 5 Status 68
- 5.5 802.1D 69
- 69 Chapter 5 Status 70
- 5.5.3 802.1D: ARP Table 71
- 5.5.4 How ARP Works 71
- 5.5.5 View the ARP Table 71
- 71 Chapter 5 Status 72
- CHAPTER 6 73
- 6.2 Loopback Test 74
- Chapter 6 Fault Menus 74 75
- 75 Chapter 6 Fault Menus 76
- CHAPTER 7 77
- 7.2 Device Reset 78
- Chapter 7 Maintenance 78 79
- 7.4 Load Factory Default 80
- Chapter 7 Maintenance 80 81
- Configuration Backup screen 82
- 2 Click the OK button 83
- 83 Chapter 7 Maintenance 84
- CHAPTER 8 85
- 8.2 Ping 86
- CHAPTER 9 87
- 9.2 Property Configuration 88
- 9.3.2 Copy to.. Button 90
- Figure 68 91
- Copy Port Screen 91
- Table 26 Copy Port Screen 91
- Figure 69 Copy Successful 92
- CHAPTER 10 93
- 10.2.2 Configuring SNMP 94
- 10.3 Remote Management 95
- 10.4 Time Setup 97
- CHAPTER 11 99
- 11.3 Priority Queue 101
- 11.4 STP Configuration 103
- 11.5 STP Overview 103
- 11.6 Link Aggregation 105
- 11.6.3 Link Aggregation ID 106
- 11.7 DHCP Relay 107
- 11.8 GARP Timer 109
- 11.9 RADIUS 110
- 11.10 MAC Forwarding 111
- 11.11 Filtering 113
- CHAPTER 12 117
- Selecting a VLAN Type 118
- 12.2.1 Modify an 802.1Q VLAN 119
- 119 Chapter 12 VLAN 120
- 12.2.2 Removing a VLAN 121
- 121 Chapter 12 VLAN 122
- Chapter 12 VLAN 122 123
- 123 Chapter 12 VLAN 124
- CHAPTER 13 125
- 13.2 Port VLAN 127
- 13.3 Port Link Aggregation 128
- 13.4 Port STP 129
- 13.5 Bandwidth Control 130
- 13.6 Broadcast Storm Control 131
- 13.7 Queue Method 132
- 13.8 Port 802.1x 133
- 13.9 Port Security 134
- 13.10 Port Mirroring 135
- 13.11 VLAN Stacking 136
- TABLE DESCRIPTION 138
- CHAPTER 14 139
- 14.2 Switch Manager 141
- 14.2.1 Access Log 142
- CHAPTER 15 149
- 149 Chapter 15 Performance 150
- 15.2 Table Menu Bar Icons 151
- 15.2.2 Expand Dialog Box 153
- 15.3 Graph Menu Bar Icons 154
- 15.3.1 Graph Styles 155
- 15.3.3 Graph Labels 156
- Chapter 15 Performance 156 157
- 157 Chapter 15 Performance 158
- CHAPTER 16 159
- Figure 115 EMS: Remove 160
- SNMPc Network Manager 163
- SNMPc Main Window 164
- Selection Tool 165
- Event Log Tool 165
- View Window Area 166
- Appendix A 166 167
- Appendix B 169
- Alarm Types and Causes 169
- 169 Appendix B 170
- Index 170 171
- 171 Index 172
- Index 172 173
- 173 Index 174
Relacionado con productos y manuales para Televisores Zyxel-communications 1
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales