ZyXEL Communications 2002 Series Guía de usuario Pagina 129
- Pagina / 161
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
VES-1000 Series Ethernet Switch
Switch-Related Commands 13-3
Bits of interest are described as follows. Four binary bits (a nibble) make up each hex digit
3
. The leftmost bit in
the first nibble denotes if the link is down or up. “0” means the link is up, “1” means the link is down.
Hex 1 0 0 3
Binary Equivalent Nibbles 0001 0000 0000 0111
The rightmost bit-pair in the last nibble show rate and duplex mode as described in the next table.
Table 13-2 Port Status Command
LAST HEX DIGIT RIGHTMOST NIBBLE BIT-PAIR RATE DUPLEX MODE
0 00 10Mbps Half Duplex
1 01 10Mbps Full Duplex
2 10 100Mbps Half Duplex
3 11 100Mbps Full Duplex
13.4 VLANs
Please refer to section 4.2.6 for some background information on VLANs in general.
The factory default port-based VLAN settings for VES-1000 Series switch are summarized below (see also Figure
13-3):
• Port 0 (the CPU management port) forms a VLAN with all VDSL ports and can use the Ethernet port(s) as the
uplink.
• The VDSL ports cannot talk to each other.
• Each VDSL port forms a VLAN with each Ethernet port and vice versa.
13.4.1 VLAN Status Command
sw vlan status
Use this command to view the port-based VLAN settings for all ports.
The factory default port-based VLAN for the VES-1000 Series switch is shown in the next screen.
3
0x2 = 0x0002
Link is up.
100Mbps,
Full Duplex
- VES-1000 Series 1
- Copyright 2
- ZyXEL Limited Warranty 3
- FCC Interference Statement 4
- FCC Warning 4
- CE Mark Warning: 4
- Taiwanese BCIQ A Warning: 4
- Certifications 4
- Customer Support 5
- Table of Contents 6
- Table of Contents vii 7
- List of Figures 9
- List of Diagrams 12
- List of Tables 13
- List of Tables xv 15
- Preface 16
- Related Documentation 17
- Getting Ready 19
- Chapter 1 21
- Switches 21
- 1.2 Applications 23
- 1.2.2 Enterprise Application 24
- 1.2.3 Campus Application 25
- Chapter 2 27
- Hardware 27
- Connections 27
- 2.3 Front Panel 28
- 2.4 Front Panel Ports 28
- 2.4.1 Console Port 29
- 2.4.2 VDSL Port Connections 29
- 2.5 Front Panel LEDs 30
- Hardware Connections 2-5 31
- Chapter 3 33
- Introducing 33
- the SMT 33
- 3.3 SMT Menus At A Glance 34
- Getting Started 38
- Chapter 4 39
- General 39
- Switch and IP Setup 39
- 4.2.1 Ethernet Port Trunking 41
- 4.2.4 GARP Timer Setup 44
- 4.2.5 GVRP 45
- 4.2.6 VLANs 45
- Port-based VLANS 46
- Tagged VLANs (IEEE 802.1Q) 46
- 4.2.7 IGMP Snooping 47
- 4.3 TCP/IP Setup 49
- Chapter 5 53
- 5.1.4 Ethernet Port Setup 56
- 5.2 Port Submenus 57
- Part III 61
- Chapter 6 63
- Route Setup 63
- 6-2 Static Route Setup 64
- Chapter 7 65
- 7.2.1 Static VLAN Setup 66
- Chapter 8 69
- Configuration 69
- 8.2 Supported MIBs 70
- 8.3 Configuring SNMP 70
- 8.4 SNMP Traps 71
- 8-4 SNMP Configuration 72
- Table 8-3 SNMP Traps 72
- System Maintenance 74
- Chapter 9 75
- Maintenance 1 75
- 9.2.1 System Maintenance 76
- Port Statistics 77
- 9-4 System Maintenance 1 78
- Table 9-2 Port Statistics 78
- System Maintenance 1 9-5 79
- 9.2.3 VLAN Status 81
- 9.3.1 System Information 83
- 9.4 Log and Trace 84
- 9.4.2 UNIX Syslog 85
- 9.5 Diagnostic 86
- System Maintenance 1 9-13 87
- Chapter 10 89
- Firmware 89
- and Configuration File 89
- Maintenance 89
- 10.2 Backup Configuration 90
- 10.2.4 GUI-based FTP Clients 92
- 10.2.7 TFTP Command Example 93
- 10.3 Restore Configuration 94
- 10.3.2 FTP Restore Example 95
- 10.4.1 Firmware File Upload 97
- 10.4.5 TFTP File Upload 99
- HyperTerminal 102
- Chapter 11 105
- Maintenance 2 105
- 11.2.1 Resetting The Time 106
- 11.3.1 Secured Client Sets 107
- 11.4 Hardware Monitor 109
- Commands 115
- Chapter 12 115
- VDSL-Related 115
- 12.2 VDSL Commands 116
- 12.2.1 Set VDSL Mode 117
- 12.2.4 Reset a VDSL Channel 118
- 12.2.7 VDSL Version Command 120
- 12.2.9 VDSL Show Command 120
- 12.2.11 VDSL Debug Command 121
- 12.3.4 Enet Fctrl Command 125
- 12.3.5 Enet Monitor Command 125
- Chapter 13 127
- Switch-Related 127
- 13.3 Port Status Command 128
- 13.4 VLANs 129
- SYMBOL DESCRIPTION 130
- 13.4.2 VLAN Set Command 131
- Sw vlan set 3 1 132
- Sw vlan set 4 1 132
- 13.4.3 VLAN Clear Command 133
- Sw vlan clear 1 3 4 134
- Sw vlan clear 1 all 134
- 13.5 MAC Address Commands 135
- 13.6 MAC Address Learning 136
- 13.6.1 MAC Address Details 137
- 13.6.2 MAC Number 137
- 13.8 Switch Driver Commands 139
- TxFreeCnt = 79287 140
- Chapter 14 141
- 14.1.2 IGMP Snooping Queries 143
- 14.1.3 Enable IGMP Snooping 143
- Chapter 15 145
- Troubleshooting 145
- 15.4 Data Rate 146
- 15.5 Configured Settings 146
- 15.6 Password 146
- 15.7 Remote Server 147
- 15.8 Telnet 147
- 15-4 Troubleshooting 148
- Appendices and Index 150
- Appendix A 151
- Hardware Specifications 151
- • 4.4 kg 152
- • 35 watts maximum 152
- • 100-240VAC/1A, 50/60Hz 152
- Appendix B 153
- Pin Assignments 153
- F Appendix B 156
Relacionado con productos y manuales para Redes ZyXEL Communications 2002 Series
Redes ZyXEL Communications G-5100 Manual de usuario
(18 paginas)
(18 paginas)
(140 paginas)
Redes ZyXEL Communications M-302 Guía de usuario
(56 paginas)
(56 paginas)
Redes ZyXEL Communications NSA221 Manual de usuario
(11 paginas)
(11 paginas)
Redes ZyXEL Communications 10 Manual de usuario
(102 paginas)
(102 paginas)
Redes ZyXEL Communications M-302 Manual de usuario
(14 paginas)
(14 paginas)
Redes ZyXEL Communications MAX318M Guía de usuario
(102 paginas)
(102 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales