ZyXEL Communications VES-1012 - Guía de usuario Pagina 180
- Pagina / 227
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
VES-1000 Series Ethernet Switch
23-2 VDSL-Related Commands
Figure 23-2 CI Commands
23.2 VDSL Commands
The following table is a summary of VDSL-related commands.
Table 23-2 VDSL-related Commands
COMMAND DESCRIPTION
vdsl uprate chan-id (x)
This command sets the VDSL upstream rate (0 to 4)
vdsl downrate chan-id (y)
This command sets the VDSL downstream rate (0 to 4)
vdsl reset chan-id [lt|nt]
This command resets the VDSL chip.
vdsl reconnect chan-id
Make VDSL reconnect
vdsl clear chan-id
Clear VDSL related counters
vdsl debug chan-id [on|off]
This command sets the VDSL debug flag.
vdsl monitor chan-id [on|off]
This command sets the VDSL monitor flag.
vdsl status chan-id
This command shows the VDSL status counters.
vdsl show chan-id
This command shows VDSL settings.
vdsl mode chan-id (mode)
This command changes the VDSL mode (0 = 10BaseS, 1 = ANSI, 2
= ETSI).
vdsl active chan-id [on|off]
This command actives/deactivates the VDSL driver.
vdsl ver
This command shows the VDSL driver version.
vdsl quality chan-id
This command shows VDSL quality.
vdsl enet status chan-id
This command shows Ethernet status counters.
vdsl enet clear chan-id
This command clears Ethernet status counters.
vdsl enet monitor chan-id [on|off]
This command sets the VDSL chip Ethernet monitor flag
vdsl enet phy chan-id
This command shows the NT Ethernet PHY registers.
“chan-id” (“vdsl01”, “vdsl02”,…”vdsl12”) refers to the channel name for each VDSL channels. “all” is also a
valid channel name that indicate all channels.
All VDSL parameters and flags set using VDSL commands are effective at run-time only. If you
restart the VES, you will lose the configuration changes you made with commands. To save
changes permanently, please use the appropriate SMT menu.
The rest of this chapter shows commonly used VDSL-related CI command examples.
ras> ?
Valid commands are:
sys exit ether vdsl
sw ip
ras>
- VES-1000 Series 1
- Copyright 2
- FCC Interference Statement: 3
- FCC Warning! 3
- CE Mark Warning: 3
- Certifications 3
- ZyXEL Limited Warranty 4
- Customer Support 5
- Table of Contents 6
- List of Figures 10
- List of Figures xi 11
- List of Figures xiii 13
- List of Tables 14
- List of Tables xv 15
- Preface 17
- Part I: 19
- Chapter 1 21
- Getting to Know Your VES 21
- SNMP V1 (RFC 1157) 22
- Bridge MIB (RFC-1493) 22
- 1.3 Applications 23
- 1.3.2 Enterprise Application 24
- 1.3.3 Campus Application 25
- Chapter 2 27
- Hardware Connections 27
- 2.3 Front Panel 28
- 2.4 Front Panel Ports 28
- 2.4.1 Console Port 29
- 2.4.2 VDSL Port Connections 29
- 2.5 Front Panel LEDs 30
- Part II: 31
- Chapter 3 33
- 3.3 Home Screen 34
- 3.4 Screen Overview 35
- Chapter 4 39
- Initial Configuration 39
- 8. Click the Apply button 40
- Chapter 5 41
- Getting Started Screens 41
- 5.3 IGMP Snooping 42
- 5.4.2 How STP Works 43
- 5.5 GARP Timer 44
- 5.6 Switch Setup Screen 44
- Getting Started Screens 5-5 45
- Figure 5-3 Switch Setup 45
- DESCRIPTION 46
- Getting Started Screens 5-7 47
- Table 5-4 Switch Setup 47
- 5.7 IP Setup Screen 48
- Chapter 6 51
- 6.4 Rate Adaption 52
- 6.5 VDSL Default Values 52
- 6.6 GVRP 52
- 6.7 Port Setup Screen 53
- Port Setup 6-5 55
- 6-6 Port Setup 56
- Port Setup 6-7 57
- 6-8 Port Setup 58
- Figure 6-3 Uplink Port Setup 58
- Port Setup 6-9 59
- Table 6-5 Uplink Port Setup 59
- 6-10 Port Setup 60
- Chapter 7 61
- Static Route 61
- Static Route 7-3 63
- Table 7-2 Static Route Edit 63
- Chapter 8 65
- 8.5 VLAN Setup 67
- Part III: 73
- Chapter 9 75
- 9.1.1 Supported MIBs 76
- 9.1.2 SNMP Traps 76
- 9.1.3 Configuring SNMP 76
- Chapter 10 79
- Chapter 11 81
- LABEL DESCRIPTION 82
- Maintenance 11-3 83
- Table 11-1 Maintenance 83
- Chapter 12 89
- Statistics 89
- Statistics 12-3 91
- Table 12-2 Show STP Status 91
- Statistics 12-5 93
- Table 12-3 Hardware Monitor 93
- 12.2.5 Port Details Screen 96
- 12-10 Statistics 98
- Table 12-6 Port Details 98
- Statistics 12-11 99
- Chapter 13 101
- Diagnostic 101
- 13.4 Logout Screen 103
- Part IV: 105
- Chapter 14 107
- Introducing the SMT 107
- 14.5 SMT Menus At A Glance 108
- 14.5.1 Main Menu 109
- 14.6.1 Resetting the VES 111
- Chapter 15 113
- General, Switch and IP Setup 113
- 15.2.2 GARP Timer Setup 116
- 15.3 TCP/IP Setup 118
- Chapter 16 121
- Port Setup 121
- FIELD DESCRIPTION EXAMPLE 122
- JoeSoap 122
- 16.1.3 Ethernet Port Setup 123
- 16.2 Port Submenus 125
- Part V: 129
- Chapter 17 131
- Static Route Setup 131
- 17-2 Static Route Setup 132
- Chapter 18 133
- VLAN Setup 133
- 18.3 Port-Based VLAN Setup 135
- SYMBOL DESCRIPTION 136
- Chapter 19 137
- SNMP Configuration 137
- 19.2 Supported MIBs 138
- 19.3 Configuring SNMP 138
- 19.4 SNMP Traps 139
- 19-4 SNMP Configuration 140
- Table 19-3 SNMP Traps 140
- Part VI: 141
- Chapter 20 143
- System Maintenance 1 143
- 20.2.1 System Maintenance 144
- Port Statistics 145
- 20-4 System Maintenance 1 146
- Table 20-2 Port Statistics 146
- System Maintenance 1 20-5 147
- 20.2.3 VLAN Status 149
- 20.3.1 System Information 150
- 20.4 Log and Trace 151
- 20.4.1 Viewing Error Log 152
- 20.4.2 UNIX Syslog 152
- 20.5 Diagnostic 153
- Chapter 21 155
- Maintenance 155
- 21.2 Backup Configuration 156
- 21.2.4 GUI-based FTP Clients 157
- 21.2.7 TFTP Command Example 158
- 21.3 Restore Configuration 160
- 21.3.2 FTP Restore Example 161
- 21.4.1 Firmware File Upload 162
- 21.4.5 TFTP File Upload 164
- HyperTerminal 167
- Chapter 22 169
- System Maintenance 2 169
- 22.2.1 Resetting The Time 170
- 22.3.1 Secured Client Sets 171
- 22.4 Hardware Monitor 173
- Part VII: 177
- Chapter 23 179
- VDSL-Related Commands 179
- 23.2 VDSL Commands 180
- 23.2.1 Set VDSL Mode 181
- 23.2.4 Reset a VDSL Channel 182
- VDSL-Related Commands 23-5 183
- 23.2.7 VDSL Version Command 184
- 23.2.9 VDSL Show Command 184
- 23.2.11 VDSL Debug Command 185
- 23.3.4 Enet Fctrl Command 189
- 23.3.5 Enet Monitor Command 189
- Chapter 24 191
- Switch-Related Commands 191
- 24.3 Port Status Command 192
- 24.4 VLANs 193
- 24.4.1 VLAN Status Command 194
- 24.4.2 VLAN Set Command 195
- Sw vlan set 3 1 196
- Sw vlan set 4 1 196
- 24.4.3 VLAN Clear Command 198
- Sw vlan clear all 199
- 24.5 MAC Address Commands 200
- 24.6 MAC Address Learning 201
- 24.6.2 MAC Number 202
- 24.8 Switch Driver Commands 204
- TxFreeCnt = 79287 205
- Chapter 25 207
- IP Commands 207
- 25.1.2 IGMP Snooping Queries 208
- 25.1.3 Enable IGMP Snooping 209
- Chapter 26 211
- Troubleshooting 211
- 26.4 Data Rate 212
- 26.5 Configured Settings 212
- 26.6 Password 212
- 26.7 Remote Server 213
- 26.8 Telnet 213
- 26-4 Troubleshooting 214
- Part VIII: 215
- Appendix A 217
- Product Specifications 217
- Appendix B 219
- Pin Assignments 219
- B-2 Pin Assignments 220
- B-4 Pin Assignments 222
Relacionado con productos y manuales para Redes ZyXEL Communications VES-1012 -
Redes ZyXEL Communications DI-106 Manual de usuario
(168 paginas)
(168 paginas)
Redes ZyXEL Communications P-841 Guia de preparacion
(21 paginas)
(21 paginas)
Redes ZyXEL Communications VSG1432 Guía de usuario
(408 paginas)
(408 paginas)
Redes ZyXEL Communications G-3000 Guía de usuario
(19 paginas)
(19 paginas)
Redes ZyXEL Communications P-2602HW-63C Guía de usuario
(465 paginas)
(465 paginas)
Redes ZyXEL Communications Prestige 642 Guía de usuario
(134 paginas)
(134 paginas)
Redes ZyXEL Communications ZyWALL 70 Información técnica
(298 paginas)
(298 paginas)
Redes ZyXEL Communications G-102 Guía de usuario
(198 paginas)
(198 paginas)
Redes ZyXEL Communications IES-1248-51 Guía de usuario
(654 paginas)
(654 paginas)
Redes ZyXEL Communications ES-305 Guía de usuario
(118 paginas)
(118 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales